This is the 1/10th Scale Glow Powered, Radio Controlled, 4 Wheel Drive
Associated TC3 Team On-Road Car Kit.
FEATURES: Chassis: 6061 T6 Anodized aluminum 2.5mm thick.
Drive: Four wheel drive.
Drive Type: Shaft driven.
Fuel Tank: 4.2oz (125cc), flip top cap
Clutch: Two-shoe type, accepts both SG and standard short crankshafts
Transmission: Two-speed, externally adjustable.
Ball Bearings: Bearings used in high stress areas, bushings in non-
critical areas.
Shocks: Four oil-filled type with coil-over springs, blue anodized
aluminum bodies. 40 weight shock oil included.
Main Gears: 54 and 50 tooth, plastic.
Engine Placement: Chassis can accomodate pull start side or rear
exhaust engines with rotary or slide valve carburetors. Header and
muffler for side exhaust engines is included.
Gearboxes: Sealed front and rear.
Differentials: planetary geared, ball differential)
Brakes: Dual pad style with cam assembly.
Tires: Proline V-Rage treaded rubber Width: 1" (26mm), Outer Diameter
2.56"(65mm), Inner Diameter: 2.00" (51mm)
Wheels: White 1-piece, ten spoke touring car, Proline Gumby with hex
drive. Width: 1" (26mm), Diameter: 2" (51mm)
Suspension: Front and rear pivot balls and symmetrical A-arms for
easier more predictable setup.
Bumper: Two part rubber mounted ABS plastic and foam front bumper.
Camber Tie Rods: Adjustable (Camber describes the angle the wheels
ride relative to the ground when viewed from the front or back).
Steering Tie Rods: Adjustable, toe-in is adjustable on front and rear
wheels.
Steering: Bell-crank type, steering rack with adjustable Ackerman.
Ackerman describes the the effect of the inside front wheel turning
tighter than the outside front wheel.
Servo Saver: included (if this applies)
INCLUDES: One 1/10th Scale Glow Powered, R/C 4WD Associated TC3 Team On-Road
Car Kit with, 1" (26mm) x 2.56" (65mm) tires with foam inserts,
1' (26mm) x 2" (51mm) wheels 26 and 22 tooth clutch bell, 54 and
50 tooth spur gear, 40 weight shock oil, aluminum bodied shocks,
muffler and header pipe for side exhaust, decal sheet, photo
illustrated instructions, caster, camber and ride height tool,
aluminum engine mounts, fuel tubing, throttle linkages and servo
horns.
REQUIRES: Radio: Two channel with two standard size servos, high torque servo
is recommended but not required.
Radio Batteries: Eight AA size
Engine: .12 or .15 rear or side exhaust pull-start engine with rotary
or slide valve carburetor.
Glow Starter: 1.2 volt
Body: 200mm touring car style.
Paint: Polycarbonate for body
Misc. Items: Fuel bottle, building and track equipment
Fuel: 2-cycle glow fuel with 10%-15% nitromethane.
Most of the fuels we carry meet or exceed the lubricant content
required for optimum performance and maximum engine life. In the
past, the conventional lubricant content used in fuel was 18%. But
with new advanced technologies, fuels like Red Alert and O'Donnell
for example, have a better quality of lubricants even though the
percentages of lubricant content are lower. These high-tech
lubricants provide exceptional cooling and protection.
SPECS: Length: 15" (381mm)
Wheelbase: 10.25" (260mm) (wheels on-center front-to-rear)
Ground Clearance: 1.37" (35mm)
Gear Ratio: 2.5:1
COMMENTS: For Replacement Ball Bearings use:
Qty. Size Location Bearing Set Qty.
4 3/16x5/16" Steering Swing Rack DTXC1413 2
4 3/8x5/8" Differential Gear DTXC1437 2
4 3/16x5/16" Differential Gear DTXC1413 2
2 3/16x3/8" Front Input Shaft DTXC1423 1
2 3/16x3/8" Main Gear Input Shaft DTXC1423 1
1 1/8x1/4" (flanged) Main Gear Input Shaft not carried
8 3/16x3/8" CVD Assemblies DTXC1423 4
1 5x10" Clutch DTXC1535 1
1 5x10" (flanged) Clutch DTXC1541 1
JXS 1/31/02
ir/kh