This is the 1/8 scale, glow powered, radio controlled, 4 wheel drive
HPI Savage 25 off-road ready-to-run Monster Truck.
FEATURES: Chassis: TVP (Twin Vertical Plate) 6061-series aluminum, 2.5mm thick
Drive: Four wheel drive
Drive Type: Shaft driven
Radio: AM pistol grip TF-4 with steering dual rate, steering and
throttle trim, and high-torque steering servo with 70 oz/in
.20 sec. @ 4.8V or 90 oz./in & .16 sec. @ 6V
Engine: HPI Nitro Star S-25 (4.1cc) with billet aluminum heatsink
head, dual bushing aluminum connecting rod, ABC chrome sleeve
construction, dual needle 7mm slide valve carburetor, and electric
push button Roto Start eliminating the pull-start from the engine
and the primer button from the fuel tank
Exhaust: Composite dual chamber tuned pipe with aluminum header
Fuel Tank: 5.4oz (160cc) with ceramic in-tank filter and rear fuel
pickup
Clutch: 3-shoe with 15 tooth clutch bell and an 18 tooth clutch bell
included for high-speed on-road driving
Transmission: Two-speed with selectable shift point with heavy duty
metal internal gears and adjustable slipper clutch
Bearings: Full set of rubber sealed bearings, 18 total
Shocks: Eight oil-filled, plastic bodied with coil-over firm black
springs
Main Gear: 49 tooth hardened steel
Gearboxes: Sealed front and rear
Differentials: Planetary type with hardened metal gears
Brakes: Fiberglass disk
Tires: 6.25" (159mm) outer diameter, 3.25" (82mm) wide, 3.6" (91mm)
inner diameter, pre-glued to wheels
Wheels: 1-piece, 3.5" (89mm) diameter, 2-1/4" (55mm) wide 4-spoke
monster truck, chrome finish
Body: Highly detailed pre-painted extended cab pickup truck with
red, silver, and graphite graphics with full set of decals applied
Bumpers: Front and rear with skid plates
Suspension: Wide track, stainless steel inboard hinge pins with
anodized aluminum braces, and standard upgraded steel dogbones
Camber Tie Rods: Non-Adjustable, camber is the angle at which
the tires sit vertically
Steering Tie Rods: Adjustable, caster/toe-in is the angle that the
tires point inward as viewed from above
Steering: Bell-crank
Servo Saver: Included
Build Time: Ready to run in about 15 minutes
Warranty Period: Two year, limited
INCLUDES: HPI Savage 25 with oil filled shocks, .25 (4.1cc) engine, antenna
tube, painted body, tires, foam inserts, 4-spoke wheels, 3 channel
radio with high-torque servo, 15 & 18 tooth clutch bell, 49 tooth
spur gear, glow plug, and instructions
REQUIRES: Radio Batteries: 12 AA size
Roto Start Battery: 6 cell, 7.2V
Battery Charger: Timed or peak for Roto Start battery
Note: If the optional Reverse Module (HPIC8703) is installed, an
additional standard servo servo must be purchased. A high torq
servo is not needed for the reverse module.
Misc. Items: Fuel bottle, building and track equipment, glow starter
Fuel: 2-cycle glow fuel with 20% nitromethane, 16% lubricant-
Most of the fuels we carry meet or exceed the lubricant content
required for optimum performance and maximum engine life. In the
past, the conventional lubricant content used in fuel was 18%. But
with new advanced technologies, fuels like Red Alert and O'Donnell
for example, have a better quality of lubricants even though the
percentages of lubricant content are lower. These high-tech
lubricants provide exceptional cooling and protection.
SPECS: Vehicle-
Length: 21" (533mm)
Width: 16.8 (427mm)
Height: 10" (254mm)
Weight: 11.2 lbs (5080g) approx.
Wheelbase: 13.25" (336mm) wheels on-center front-to-rear
Tread-Front-Rear: 12.9" (327mm) wheels on-center side-to-side
Track-Front-Rear: 16" (407mm)
Suspension Travel: 6" (152mm)
Ground Clearance: 3" (76mm) at lowest point
Body-
Length: 18" (457mm)
Width: 6-7/8" (175mm) at rear wheels, widest point
6" (153mm) behind from wheels, thinnest point
Height: 10-3/4" (273mm)
COMMENTS: This kit is also compatible with Traxxas T-Maxx bodies, wheels, and
tires
Some key differences between the HPI Savage 21 RTR, Savage 25 RTR,
and the Savage SS:
Savage 21 Savage 25 Savage SS
Engine 21BB Nitro Star S-25 Nitro Star S-25
Tuned Pipe composite, dual composite, dual polished aluminum
chamber chamber ribbed
Starting
System pullstart Roto Start pullstart
Spur Gear 52T 49T 49T
Clutch Bell 14T 15T, 18T 15T, 18T
Clutch Type two shoe three shoe two shoe
Shock
Springs red medium black firm purple firm
w/primer w/o primer w/primer
Fuel Tank front pickup rear pickup front pickup
Body black silver purple red black gray clear
Dogbones updt standard updt standard heavy duty silver
For Replacement Ball Bearings use:
Qty. Size Location Use Bearing Set Qty.
4 8x16x5mm fr & r gearbox (2) DTXC1585
4 10x16x5mm fr & r gearbox (2) HPIC2032
8 8x16x5mm uprights (4) DTXC1585
1 8x16x5mm 39t trans. gear (1) DTXC1585
5 6x13x5mm center gearbox (3) DTXC1573
1 8x16x5mm center gearbox (1) DTXC1585
2 5x10x4mm clutch bell (1) DTXC1535
Body pictured on the box is painted red, silver, and gray
It is not possible to request a specific radio channel when ordering
because they are supplied by the manufacturer at random.
jxs 9/15/03
ir/jxs
updt jxs 11/19/03